GMADE 1/10 GS02 TA PRO CHASSIS KIT

Special Parts

GS02 TA Pro Chassis Kit some parts are relaced with the following parts:

G502 Hardened Universal Shaft

GA44 Heavy Duty Diff Locker

GA60 Brass Steering Knuckle Bushing

Alumionium 12mm Wheel Hub (4)
(8mm Thick)

Aluminium Ball Set For G502 Chassis (Silver)

Shock Spring Soft Green 16.2x36mm (2), 15.2x61mm (4)

Shock Spring Hard Red 16.2x36mm (2), 15.2x61mm (4)

Frame

Steel Ladder Frame

GS02 frame is designed to look like a chasssis of a real car frame and the material of the frame is made of high strength steel, C-Channel side rail and is with hex wrench bolted cross members, which make it resistant to twisting or wrapping.
Also, steel parts are black powder coated finish to prevent rust.

C-Channel Side Rail

Adjustable Wheelbase

GS02 chassis allows three type of easy adjustment of wheelbase converet kit to use any type of 300, 313 and 324mm custom bodies,
(optional link kits are sold separately)

Front Weight Balance

BOM’s weight balalnce designed to be placed on the forard of the car.
This will increase the tire traction to the front wheel to provide better crawling on high tilt angle rocks and better driving performance when hill climbing and this will help minimise the vehicle rolling over when climbing.

Chassis Mounted Servo System with Panhard Bar

BOM’s steering system has a steering servo on the frame just like a 1:1 real car.
It is designed to make it as close to the zero bump steer so bump steer movement does not appear by front wheel suspension movements.
So we ended up with maximising the steering performance of the vehicle.
In additionm, the Panhard-bar is designed to avoid intererence with nearby parts, so that the front suspension and shocks can move freely without and loss.

Waterproof Receiver Box

The waterproof receiver box protects thereceiver from water, mud and snow.

Battery Tray

The battery can be easily replaced and can accomodate up to 7,600mAh 2-cell Lipo batteries or 5,000mAh 3-cell Lipo batteries.

Dust Proof Electronics Box

It protects electronic equipment such as winch controllers and BEC, which arte often used for scale trucks, from foreign substances.

Front and Rear Bumper Mount

Mount to mount Width: 43mm

Skid Plate

The skid plate protects the transmission and other critical componenets by the flat surface that allows the BOM to slip and ride on rocks and other obstacles easily.

Drive Train

Drivelines

The drivelines of the front and rear axles are arranged instraight-line to reduce fatigue sress of the universal shaft and reduce the loss of driving power by providing efficient driving lines.

Torgue Twist Reduce Transmission

The TTR transmission is designed to drive in a stable position without pulling the balance of power transmitted to the axle.
The front and rear universal shafts based onm tghe transmitter each rotates clockwise and anti-clockwise, this componsates for the forces acting on the opposite rotational forces due to the action (torgue) and reaction (reverse torgue) because this vehicle can run in a super stable condition.

Dual Slipper Clutch

The slipper pads arfe designed to hold the spur gears evenly to allow more precise settings.

All Metal Internal Gears

Hardened Carbon Steel Universal Shaft

Easy Adjust Motor Mount

You can easily replace and install the motor pinion gear to changing the gear ratio.

GA44 Axle

The GA44 axle is designed with the hardcvore rock crawler in mind.
Axles are made of high strength materials, and it will look and perform off-road as a real 1:1 vehicle when a 4-link suspension is added. The GA44 axle is housed in a duarable one piece.
The angle of the differential cover is designed to reduce the risk of damage due to frontal impact and is therefore suitable for off-road driving.

Body Post

Adjustable body post is included to mount different body types

Suspension

SD Scaler Shock Absorber

SD Scaler Shock is a coil cover styled oil shock absorber opmimised for the cale trucks. The oil filled inside the shock minimises splash when the vehicle is driven, and provides a high-durability aluminim shock body with 3.5mm heavy duty shock shafts are added, these will help you to drive roughly on roufgh surfaces. Beginners also can easily assemble this shock and change set-ups, and the adjustable nut makes it easy to adjust the ride height so you can quickly change your car setup even when driving conditions change.

Rear Cantilever Suspension System (Select System Rear Suspension)

The GS02 Rear Cantilever Suspension System is desaigned for efficently use of custom flat beds, full drop beds and the interiors.
It also provides smooth motion of the shock ands big wheel travel.

Rear Shock Relocation Kit (Select Setup Rear Suspension)

Extra parts are included in the kit so that you can change the different types of shock mount positions.

Rear Shock Hoop

Spec